U E D R , A S I H C RSS

Robot_Study/Introduction_to_Robotics

Difference between r1.52 and the current

@@ -1,158 +1 @@
[[TableOfContents]]
 
== Information ==
Purpose: Learning basic knowledge of robotics
Lecture: CS223A, Stanford University
Date: Jan 21, 2019 ~
 
* Prerequite
- Linear Algebra
- Numerical Analysis
(or graphics programming experience)
== Reference ==
Material: Copy from Stanford
Video clips: https://www.youtube.com/watch?v=0yD3uBshJB0&list=PL65CC0384A1798ADF
 
== Study List ==
=== Lecture 1: Spatial Description ===
General Manipulator: Robot Arm, using Revolute joint, Prismatic joint
- Robot Arm: base, link, joint, end-effector
- Revolute joint: Rotation movement, 1 Degree of Fredom(DoF)
- Prismatic joint: Linear movement, 1 DoF
- Denote joint type using ε(0 for revolute, 1for prismatic)
 
Discription of body1 (9 parameters)
- Link location: 3 points (Each point has 3 parameters)
 
Discription of body2 (6 parameters)
- Body orientation: 3 parameter
- Point on the body: 3 parameter
=> Robot arm(n:links, 1: base) has n DoF
 
Transformation
- Pure Rotation
- Pure Translation
- General Tasformation
- Inverse Transformation
 
Configuration Representation
There is no universial agreement in the field of robotics as to what is the best orientation representation.
Because each representation hase advantages and shortcomings
- Direction Cosines:
- Euler angle representation: ZYX, angle(α, β, γ)
- Fixed angle representation: XYZ, angle(γ, β, α)
- Inverse of an orientation representation
=== Lecture 2: Direct Kinematics ===
Previous
- Independent of the structure of the manipulator
 
Introduction
- A set of parameters specific to each manipulator
- ex) rotation, translation, link of manipulator
- Forware Kinematics
- Inverse Kinematics
 
Link Description
- Manipulator: Consist of a chain of links from base
- Consecutive links are connected by joints which exert the degree of freedom.
 
D-H Parameter
- link length(a): length along the common normal from axis (i-1) to axis i
- link twist(α): angle between this parallel line and axis (i-1)
- link offset(θ): distance alont the line on axis i between the common normal for link (i-1) and common normal for link i
- joint angle(d): angle between the two common normal for link (i-1) and common normal for link i
- Revolute joint: joint angle(variable), link offset(constant)
- Prismatic joint: joint angle(constant), link offset(variable)
- a, α: describe link
- d, θ: describe the link's connection
 
Conventions for First and Last Link
- Once robot structure is set link length & link twist is determined.
- a(i) and α(i) depend on joint axes i and i+1
Axes 1 to n: determined => a(1), a(2), ,,,, a(n-1) and α(1), α(2), ,,,,a(n-1)
- d(i) and θ(i) depend on
 
Attaching Frames to links
- ex1) RRR (Revolute-Revolute-Revolute) Manipulator
- ex2) RPRR (Revolute-Prismatic-Revolute-Revolute) Manipulator
 
Propagation of Frames
- Show how to calculate matrix about D-H parameter
- Reference
http://www.adrian.zentner.name/content/projects/xml/x3d/robot/res/Denavit-Hartenberg.gif
 
Kinematics of Manipulators
- Example of robot arm (Stanford Scheinman Arm)
- Reference
http://infolab.stanford.edu/pub/voy/museum/pictures/display/robots/StanfordArm.jpg
 
Direct(forward) Kinematics
- Mapping between the joint space of dimension n and the task space of manipulator of dimension m
- Called the "Geometric Model of the manipulator"
(It is determinded solely by knowing the geometry of manipulator)
- q(i) = ε'(i)θ(i) + ε(i)d(i)
- X = f(q)
=== Lecture 3: Inverse Kinematics ===
Introduction
- Difficult task: Multiplicity or non-existence of potential soultions
- Problem: find q given T(B,W) or x / find q = f^(-1)(x)
 
Closed Form Solutions
Algebraic: solution is found using the fact that θ1+θ2+θ3 = a0
Geometric: there are two possible solutions
 
Piper's Solution
???
 
Existence of Solution
- If these two equations are correct, solution of the inverse kinematics exists
- However, sometimes there is no solution because of limitation of robot model
 
Workplace of the Manipulator
- Workspace: the set of points that can be reached with the mainpulator
- Joint limitation is always defined by the mechanical design of the manipulator
* Related question: # of possible solutions
- Reachable Workspace: the set of points that can be reached in at least one conficuration of the manipulator
- Dextrous workspace: the set of points that can be reached by any possible orientation of the end-effector, important in the motion planning with obstacles (Reachable Workspace > Dextrous workspace)
 
# of Solutions
6R manipulator: 16 solutions
5RP manipulator: 16 solutions
4R2P manipulator: 8 solutions
3R3P manipulator: 2 solutions
in-parallel structures: 40 solutions
 
- Puma Robot
Reference
https://d2t1xqejof9utc.cloudfront.net/screenshots/pics/45f6b6d1d881d687d15e29d47f181a6f/large.PNG
 
- Stanford Scheinman Arm
Reference
http://infolab.stanford.edu/pub/voy/museum/pictures/display/robots/IMG_2404ArmFrontPeekingOut.JPG
 
=== Lecture 4: The Jacobian ===
Previous
- Establish the mathematical models which describe the relationships between the static configurations of a mechanism and its end-effector
 
Introduction
- Establish the relationship between δx and δq
- The relationship between δx and δq is described by the Jacobian matirx
- This matrix is key to the relationship between joint torques and end-effector forces
 
Differential Motion
- X = f(q)
Reference
https://ipfs.io/ipfs/QmXoypizjW3WknFiJnKLwHCnL72vedxjQkDDP1mXWo6uco/I/m/74e93aa903c2695e45770030453eb77224104ee4.svg
 
Example
- RR Manipulator
- Stanford Scheinman Arm
 
 
 
== Comments ==
선배님 너무 멋있어여 - [조예진]
* 새싹 준비입니다 - [우준혁]
 
== Back page ==
* [우준혁]
[DeleteThisPage]



Valid XHTML 1.0! Valid CSS! powered by MoniWiki
last modified 2021-02-16 14:07:44
Processing time 0.0289 sec